|
|
|
Baby Clipart for all your Baby Shower Printing Needs
Baby clipart is the perfect accent to all of your baby shower printing needs. Whether announcements, invitations, thank you notes or stationery. Baby shower clip art can help you design the perfect original card or flyer for any event, but it’s most...
Can’t Find A Very Wide Selection Of Plus Size Clothing?
Haven’t got a thing to wear and that all-important evening is getting closer? Well with the wide selection of plus size clothing that’s on the market today you should be decked out in fine style by the time that evening rolls around. Today’s market...
Don't Want Another Carpet Sweeper This Year For Christmas? Unique "Sent-A-Hint" Plan Sends Your Gift Wishes Via E-mail
Sure, they love you and each year they try their best to find you the perfect gift. But let’s be honest, sometimes they need a little help. Here’s your chance to let your husband, parent, or special someone know exactly what you want. Sign up now...
Gift Ideas for Men: Birthday Gift Ideas
Unique Presents for Men (...especially on their birthday!) Many women find it hard to find unique birthday gifts for their men. But, if you know just a little bit about that man you can find several unique and unforgettable gifts. If your man...
How To Have A Happy And Healthy Back To School
It's the time of the year that most kids have been avoiding; Back To School! Going back to school can make some kids anxious. Some are starting kindergarten and others are transitioning from elementary to middle school or from middle school to high...
|
|
| |
|
|
|
|
|
|
Creating A Baby Belly Mold Part 2 of 2
Welcome Back to Creating a Baby
Belly Mold
Step Four:
Now comes the fun part. You want to have a couple of bowls of water handy. Change
the water if it starts to get "creamy".
Instructions for the plaster depends on the kind you buy but they are all are
pretty close.
Fill the bowls up with water, tempeture should be around 22-25 degres celcis.
Take the bandges and immerse them into the water for 3-5 seconds. When you take
the bandgage out hold the 2 ends up in the air close to each other and let the
extra water drip off.
Now start applying the banges from top down or the bottome up (it doesnt matter).
When appling the bandages apply them in a angle. Dont apply then straight across
the belly. If you apply them straight across it will not be as stong as if you
did it on an angle.
Keep doing this all the way up or down.
When we finished we went back over the entire mold again , just to give it a
little extra strenght. Try to do the second before the first hardens.
Step Five:
Now you have to wait until the mold dries. As the mold dries it will give off
heat, this is normal.
How long it takes to drie depends on how many coats your put on , how wet the
cast was and
what temp the water was. It took about 15 minutes before we could
take our mold off.
The easiest way to tell is reach down the side of the mold and try to pull it
off a bit, if it is really flemzy then leave it until it is somewhat firm.
While you are waiting the person helping can start to clean up the mess you
made. The plaster will come off with soap and water, its easier to get off when
its still soft.
When you think its time to remove the mold , pull up on the seran wrap , not
the mold . The seran wrap will come off very easily.
Put the cast at room temp somewere out of the way and let dry until its harded.
Step Six:
Now its time to finish your mold.
You don't have to sand it but if you want it smooth then take 80 grit sand paper
to the mold. Sand it until its smooth.
Now you can paint your mold, let your imagination go wild here. Remember little
babies love bright colors.
The only thing i can suggest is use a water base paint, some paints will eat
the plaster .
That's it your done.
I hope this will preserve your beautiful belly for a life time to come..
About the Author
Author is the writer for many sites including Las
Vegas Help. and Baby Shower Help
|
|
|
|
|
|